![]() |
| Cutting steel sheet with an angle grinder Public domain image by byrev on Pixabay |
Iron is a ubiquitous material, widely used since ancient times for its strength and durability. Its first use was probably for making tools and weapons. The alloy steel, a stronger material, made from a combination of iron, carbon and other elements, was a later discovery.
It’s now employed in a variety of fields including construction, manufacture of hand and power tools, components of machines and vehicles. We also come across it in the fabrication of more familiar items around the home such as furniture and roof sheeting.Cutting steel can be a challenge because it’s hard and tough, but there are several tools and methods that can be used. A couple of these are beyond the reach of the average DIYer because of the high cost of the equipment, but there are probably ten other methods that we can use to cut it and other common metals.
What Factors Need to Be Considered When Cutting Metal?
Several factors determine what tool and method can be used:
- Thickness of the metal
- Cost of cutting equipment
- Speed at which cutting needs to be done
- Width of cut
- Does a cut need to be curved or a series of straight line segments?
- Environment. Is there a large risk of fire or explosion?
- Does the item have to be cut in-situ or can it be removed and cut in a more convenient location?
- Are there restrictions in space where a workpiece is cut?
A Short History Lesson
In ancient times, and even today, there were two basic methods for shaping metal. These are casting and forging. Casting involves heating metal until it melts and becomes a liquid. Then it can simply be poured into a mould and allowed to cool. When it’s released from the mold, a casting assumes the shape of the mold.
Forging, on the other hand, involves heating a metal until it becomes red or white hot. At this temperature, it becomes pliable or plastic like toffee and can be shaped. In modern times, oil and gas is used to heat metal until it’s white hot, and complex machine tools can do the shaping, but ancient blacksmiths had a more simple setup.
A coal, coke or wood-powered forge with a bellows to raise the temperature was used to heat steel until it was soft and pliable. Then a variety of tools could be used to bend, twist, draw out, punch, swage and cut the workpiece. One of these tools was the hot cut which was like a chisel with a side handle. The blacksmith or his assistant held it in one hand, while striking it with a hammer in the other. This allowed sections of metal to be cut.
12 Tools for Cutting Metal
1. Hacksaw
The invention of the metal cutting hacksaw meant that a forge wasn’t necessary and steel or other metals could be cut while cold. A hacksaw can be used to make accurate, fine cuts in metal using HSS steel or titanium-coated blades.
Hacksaws are suitable for cutting small sections of metal or hollow, structural steel stock such as flat section, tube, box and angle iron. However, the process can be slow, tiring and laborious and blades need to be replaced as they go blunt.
A general-purpose hacksaw has a frame that holds a disposable fine-toothed blade under tension. A smaller junior hacksaw can be used for finer work and cutting copper tubing used in plumbing.
Advantages:
- Good for fine cuts and the narrow thickness of the blade gives accurate results
- The tool is inexpensive
Disadvantages:
- Slow for cutting thick sections
![]() |
| A hacksaw © Eugene Brennan |
![]() |
| A junior hacksaw being used to cut copper plumbing tube © Eugene Brennan |
![]() |
| Cutting a slot in 10 mm steel with a hacksaw © Eugene Brennan |
2. Tin Snips (Metal Shears or Aviation Snips)
This is effectively a scissors for cutting sheet metal up to 1.2 mm (18 gauge or 3/64″) thick.
Advantages:
- Just like a scissors, it can be used to cut curved shapes
- Tool is inexpensive
Disadvantages:
- Limited cutting thickness
![]() |
| Aviation or tin snips © Eugene Brennan |
3. Reciprocating Saw
This is like a handheld, electric hacksaw. Reciprocating means the blade slides in and out of the saw. This type of saw is frequently used for demolition work when rebar or pipes need to be cut. Blades are disposable, and just like a hacksaw, HSS steel and bimetal blades are available which are made from HSS steel, coated with titanium to make them more durable.
Advantages:
- Ideal for fast and rough cutting of a variety of materials, including metal, plastic and wood, and trimming tree limbs
- Cost similar to that of most power tools
Disadvantages:
- Not terribly accurate because of the bulkiness of the tool and difficulty of controlling angle of cut
![]() |
| A reciprocating saw and blades © Eugene Brennan |
4. Jigsaw
A jigsaw is a type of reciprocating saw, but it’s generally used on a flat surface and moved horizontally. While jigsaws are commonly used to cut curved sections in plywood, OSB and other sheet timber, they can be fitted with titanium-coated, bimetal blades, suitable for cutting sheet metal up to 6 mm (1/4″) thickness.
Advantages:
- Mostly suitable for sheet material such as roof cladding
- Possible to make curved cuts
Disadvantages:
- Slow for cutting material more than 1 to 2 mm (3/64″ to 5/64″) thickness
![]() |
| Jigsaw © Eugene Brennan |
5. Angle Grinder
This is another type of handheld power tool consisting of a motor driving a spinning, abrasive disk. The disk rotates at speeds of up to 15,000 RPM and uses friction to effectively burn through steel.
Grinders range from small cut-off tools with 75 mm (3″) disks used by auto-mechanics doing work in awkward, confined spaces to large Consaws with 300 mm or 350 mm (12″ or 14″) disks used for cutting steel girders and other large metal sections. For more information on angle grinders, see my guide “How to Use an Angle Grinder Safely for Cutting and Grinding”.
Advantages:
- Cutting material up to 6 mm (1/4″) is faster than using a hacksaw, snips or reciprocating saw.
Disadvantages:
- Grinders generate lots of sparks that can be a fire hazard or damage surfaces such as glass and paintwork. Non-abrasive, diamond-coated disks, however, are now available that don’t produce sparks.
- Only possible to make curved cuts in the end of workpieces by making lots of straight cuts and removing sections
- Cut edges can be quite rough and need to be finished by grinding.
- Cutting material greater than 6 mm (1/4″) can be slow, unless a a more powerful and cumbersome angle grinder is used.
![]() |
| Cutting angle iron with an angle grinder, fitted with a 4 1/2″ (115 mm) abrasive cutting disk. © Eugene Brennan |
6. Metal Cutoff Saw
This is effectively an angle grinder with a hinged mounting on a base. Steel sections can be clamped in a vice attached to the base and adjusted to a desired angle, allowing mitred (angled cuts). These power tools usually have a large diameter disk, typically 255 mm (10″) for cutting through thick sections.
Advantages:
- Gives a more accurate cut than a handheld angle grinder and is suitable for cutting steel that needs to be welded together to make frames, gates etc.
Disadvantages:
- Just like a hand-held grinder, a cutoff saw produces lots of sparks. However, similar to angle grinders, diamond-coated disks and toothed metal cutoff disks are available. The latter need to be used in a saw designed for these disks, e.g. an Evolution Metal Cutting Chopsaw.
![]() |
| Metal cutoff saw © Eugene Brennan |
7. Circular Saw.
Circular saws are available equipped with a metal-cutting blade for cutting sheet metal. These blades can only be used in a saw specially designed for the task (e.g. an Evolution Circular Saw), not a standard circular saw for cutting timber. A circular saw is ideal for making long, straight cuts in thin to medium thickness steel.
Advantages:
- Good for making accurate straight cuts when used with a guide.
- Doesn’t generate sparks.
Disadvantages:
- Not suitable for thick sections or non-sheet metal, as the sole plate of the saw has to stay flat and in contact at all times to prevent kickback.
8. Plasma Cutter
This works by generating an electric arc and hot plasma that melts metal in close contact with the copper tip of a hand-held cutting torch. At the same time, a jet of compressed air emerging from the centre of the tip and generated by an air compressor blows away the molten metal as the torch is moved, producing the cut. Some plasma cutters have an integrated air compressor; others can be supplied with air from a standard workshop compressor.
Advantages:
- Can cut through thick steel 12 mm (1/2″ thick) or more, depending on amperage. Relatively inexpensive for low amperage models, costing about the same as an arc welder.
- Good for making curved cuts in metal, unlike an angle grinder.
Disadvantages:
- The hot metal blown from a cut can be a fire hazard.
- The width of a cut can vary widely depending on amperage. Also, the top of a cut can be wider than the bottom or vice versa, resulting in non-square edges, requiring grinding.
![]() |
| Hanheld plasma cutter torch in use cutting sheet metal © Lidl Ireland |
9. Oxy-Fuel Cutting
Oxy-fuel cutting is a process that uses a mixture of oxygen and fuel to produce a very hot flame at a temperature of greater than 1000° C (1832° F) to cut through steel. Oxy-fuel systems include oxyacetylene, oxyhydrogen and oxypropylene. The flame is produced using a handheld cutting torch and compressed gas is stored in two steel cylinders.
Advantages:
- Suitable for cutting plates up to several inches thick
- No need for electricity, and the cutting set is portable; the cylinders carried on a hand truck
Disadvantages:
- Precautions always need to be taken to maintain the cutting set and check for any gas leaks or other faults. Operators need to be aware of the potential hazards of using compressed gas.
- Certain components of the cutting set need to be inspected/replaced at regular intervals.
- The kit can typically cost up to £800/$970.
- Gas bottles usually can’t be bought outright and must be rented.
10. Powered Shears
This tool works like a tin snips and can be electrically powered, battery powered and cordless or pneumatically powered. A nibblers is similar, but repetitively “bites” off pieces of metal as it’s pushed forwards. Nibblers allow tighter curves to be cut because unlike a shears which has a long jaw, they have a small diameter cutting head that can be simply rotated to change direction as it’s pushed forwards. A nibblers however cuts slower.
Advantages:
- No heat generated, so doesn’t burn or scuff paint on metal sheeting such as cladding
- Edges are square cut, so less ragged than the results produced by an angle grinder
- Curved profiles can be cut and even tighter curves with a nibblers.
Disadvantages:
- Cutting capacity is limited to about 1 mm to 2 mm (19 gauge to 14 gauge, 0.04″ to 0.08″)
- Cutting head is about 8 mm (5/16″) wide, so not possible to cut tight curves.
![]() |
| Pneumatic shears © Eugene Brennan |
![]() |
| Cutting head of pneumatic shears © Eugene Brennan |
![]() |
| Cordless nibblers. Image courtesy of and © Bosch Professional Power Tools |
11. Waterjet Cutting
Waterjet cutting is a process that uses an extremely high pressure jet of water (55,000 psi) mixed with an abrasive to cut through metal. This is a very clean technique, producing narrow cuts, typically down to 0.1 mm wide (0.004″) and capable of cutting material from 1 mm to 200 mm (3/64″ to 7 7/8″) thick.
Waterjet cutting machines are expensive CNC machine tools, out of the reach of the average DIYer, not handheld power tools. Designs are stored on a computer, and the design is used to control the motion of a cutting head as it moves over the material to be cut.
Advantages:
- Clean, accurate cuts of various types of materials over a wide range of thicknesses.
- Ideal for cutting materials such as plastic and aluminium that can be damaged by heat.
Disadvantages:
- The cutting equipment is very expensive.
- Not portable, so it’s not possible to cut workpieces in-situ.
12. Laser Cutting
This is a CNC process using a laser beam to vaporise material and produce a cut. Just like waterjet cutting, designs are stored on a computer which controls movement of a cutting head. Cuts as narrow as 0.1 mm are possible, depending on the quality of the optics used. Laser cutters are expensive but not exorbitantly so, therefore they’re within the budget of home users.
![]() |
| Laser cutter. Public domain image by OptLasers on Pixabay |
Metric to Imperial (Inch) Conversion
![]() |
| Metric to decimal and fractional inch conversion. Fractions are to the nearest 64th. © Eugene Brennan |
Disclaimer
This article is accurate and true to the best of the author’s knowledge. Content is for informational or entertainment purposes only and does not substitute for personal counsel or professional advice in business, financial, legal, or technical matters.
© 2023 Eugene Brennan















No comments:
Post a Comment